Look to building science and having a proper assessment performed to help you make the right improvement choices for home comfort in the hot summer months. 

A new HVAC system is likely not the right solution for a cooler home when it is blazing outside!

Temperatures in the attics of Maryland homes during summer months can go as high as 150-160 degrees.  It is a brutal place with stifling air and high amount of humidity. 
 

Healthy Attic  vs. Unhealthy Attic 

When an attic is not properly vented, air sealed and insulated the stagnant hot air and pressure is too much for an old insulation system making summer days at home a drag. 

Add leaky ducts to the situation and it makes for a long, hot summer.
 

Watch how this BPI Certified Pro and Owner of Insulwise in PA
Breaks it Down in this Excellent Animated Video

Consider this:

Maryland homeowners that have a minimum insulation level in the attic equal to R-19, reflective roof shingles and proper ventilation can experience up to two-thirds less solar heat gain than those with characteristics such as little to no insulation, dark roofing shingles and no attic ventilation. 

There are five things we recommend to make an impact on your summer comfort.

1. Air Seal Your Attic
2. Insulate Your Attic
3. Seal Your Accessible Ducts 
4. Encapsulate Your Crawl Space
5. Improve Attic Ventilation

 1. Air Sealing Your Attic

If you want to know if you should air seal your attic, then you can ask yourself a few basic questions and quickly arrive at the answer. 

The easiest way to know is to determine if you have air sealing in your attic now.  If not, then you definitely need air sealing.

When the hot build up of air in the attic creates pressure then the cracks that are left unsealed are gateways for the heat to enter your home.

If you want to learn much more about air sealing and watch how it is done in different areas of your attic and basement then check out this cool article with demos...

2. Insulate Your Attic

If you are having comfort issues in your home there is no doubt that a good place to start looking for answers is in the attic.  

Maryland attic insulation projects can be better understood and considered with a little effort and knowledge.

To get things going you must identify two main things so use this recent write up as a guide to figuring out if insulation is your next move to beat the Maryland summer heat!

3. Seal Your Accessible Ducts

When it comes to improving home comfort and energy efficiency it is amazing how little attention is paid to sealing HVAC ducts.  Properly sealing leaky HVAC ducts should be a high priority for energy efficiency and comfort.

According to the EPA and other studies, the HVAC ducts in your home can be leaky enough to account for up to as much as 30% of a household's total energy loss. 

So, what can you do?  Check out this article with great information on next steps you can take to seal your accessible ducts.

4. Encapsulate Your Crawl Space

Let’s face it – you want nothing to do with your crawl space.  You just assume that it does not exist.  You ignore it.  You board it up, lock it and put it out of your mind! 

But, it keeps reminding you it’s there.  In the summer when you go down to wash the laundry and you get a whiff of that musty odor that only comes out when it is humid. 

A few years ago you poked your head in the crawl space for one reason or another and you noticed several pieces of insulation falling down.

Read this article on what to do with crawl space vents, walls and how to properly seal it up!

5. Improve Attic Ventilation

Typically, condensation in the attic starts due to a moisture issue created by introducing two completely different air masses.  A possible issue in summer if the attic is not ventilated properly will certainly contribute to an uncomfortable home.

In hot months a leaking AC HVAC duct in an attic and other HVAC related inefficiency can allow air to seep out and interact with the hot humid attic air, particularly if the attic is not well vented.  This will cause mold and can result in comfort issues.

Read this article to get more insights into how baffles work to ventilate your attic.

What next steps can you take if this all makes sense to you, but you are not sure where to start?

You should sign up for a home energy audit...

Through BGE Here

Through Pepco Here

For only $100 through the Home Performance with ENERGY STAR Program - I am qualified to get all of the answers for you!

If you are always asking yourself, your spouse, your brother, a friend or just about anyone that will listen...

Why is my energy bill so high all of the time?

Then read this short article for key insights and actionable ways to fix your issue.
 

Three Dimensional Thinking

First, to make a house energy efficient you've got to tighten your building's shell and usually the first thing that comes to mind for most people is windows and doors.  

But, residential energy consultants know there are many other places that need attention due to physics and pressure inside your home, especially at the top and the bottom.

Have you ever noticed at one time or another that a door inside your house is particularly hard to open or that suddenly it slammed shut when otherwise on any other day, it would simply close behind you? 

The takeaway is that there are pressure dynamics going on inside your home and sometimes it is noticeable and other times you have no idea.

So, don't overlook this when asking yourself about your energy bill and use this article to begin the "hunt" for the places that can easily be fixed.  Once discovered, you will have more control over your comfort and the energy bill.

One great cost-effective example that the majority of homes have is some type of attic access panel.  In most cases, these areas are not insulated or sealed properly and they will greatly reduce the overall R-value of the rest of your insulation.

Click to watch treatment to the hatch for ideas about how you can do it at home.
 

Getting Control of Your Home's "Breathing"

How many times have you heard somebody say "a house needs to breathe"?

The "breathing" is the start of your problem.  Yes, we want our homes to "breathe", but we must consider uncontrolled breathing compared to controlled breathing.

Uncontrolled air leakage occurs when air moves through gaps or openings in walls, floors, ceilings, duct work, doors or windows to the outside and is often a major source of energy loss in homes.

Another way to look at this is by considering how we behave on cold winter days.  Most people jump out of their skin when they realize a window was left open and most people will close it right away.

Consider this:

What if all of the holes and gaps around your house are equivalent to three open windows? 

What if you could seal enough of those areas to close two of them? 

This would mean that you have a lot less energy loss and you can still breath!

In today's technologically advanced world, it is not difficult to figure out how much air a house exchanges with the outside on an hourly basis with just a few measurements and blower door test so that properly controlled ventilation can be added if a house gets too tight.

Why Air Sealing Your Home is So Important

For every little bit of conditioned air that leaves through the cracks and crevices around a home it gets replaced with outside, unconditioned air. 

And, that is very costly!

When reviewing information from an energy audit report, the story becomes much clearer in terms of where we must look to be more efficient and it is not because the lights are on too much.  Also of interest, windows and doors account for very little overall leakage when tested.

The green portion of the pie chart is the baseload.  Baseload refers to everyday stuff like lights, computers, fridge, etc. the largest load is the refrigerator so if you are already using ENERGY STAR then there might not be too much more room to save.  Efficient light bulbs will help too.

Next, look at the red and light purple.  Those show the heating and cooling costs.  

Consider the most important thing to understand when it comes to making an impact on heating and cooling usage/ costs:

You can put the world's most efficient HVAC system into a leaky house and get zero results.

In other words, don't put the cart before the horse. 

Sealing up holes, gaps and cracks around the "shell" of a home is a great way to really move the needle and will make any age HVAC system more efficient and seem like brand new. 

Where to Begin Looking for Opportunities

The pressure inside a home is greatest at the top of the building and the bottom of the building so looking in those two places will yield the lowest hanging fruit.

1. Seal Recessed Light Fixtures

The first thing you can do to save energy at home and reduce drafts is seal up you recessed lights in ceilings that are below the attic.  These common fixtures are secret gateways to the attic which means energy loss and comfort challenges. 

Most older recessed lights have ventilation holes so that heat from the bulb can escape.  Energy customers with recessed lights typically have some of the biggest bills and comfort complaints.

Check out this photo I took of a group of recessed lights from the attic. 
I turned off the flash and my headlamp.

A recessed light as seen from inside of the house.

You can seal your recessed lights from the inside with an LED recessed light kit.
 

2. Seal Attic Floor Cracks, Holes and Gaps

Similar to the recessed light problem, there are other holes and cracks in the attic floor that will lead to the communication of air between the inside of the home and the attic, or outside.  Foam sealant can be purchased at the hardware store and it can be applied to the tops of walls, around light fixtures and to seal up holes drilled for electrical wires.  All of these voids contribute to a high bill and uncomfortable living space.

Wires run through the walls to hook up to electrical outlets and switches
creating pathways for air to connect between the inside and outside (attic).

A properly sealed top of the wall looking down at the attic floor.
 

3. Seal Accessible Leaky HVAC Ducts

Saving energy at home can be achieved when you put resources in the right place.  According to the EPA and other studies, the HVAC ducts in your home can be leaky enough to account for up to as much as 30% of a household's total energy loss. Sealing ducts is not something that needs to be done by a contractor.  This is a "weekend warrior" type of project that requires a little patience, a few materials and a little know how.  Sealing ducts near the air handler will also help you the most and those are usually the places that are most accessible.

Disconnected ducts are big energy wasters!

One way to fix leaky ducts is to use two-part spray foam.

Sealing ducts with mastic is another option to save energy at home
 

4. Seal and Insulate the Basement Rim and Band Joist

If you want to save energy at home and improve comfort, be sure to think about the unfinished areas of your basement, particularly at the top of the foundation walls.

Watch this to Learn How to Seal a Basement Rim Joist

5. Install a Chimney Balloon

If you have a fireplace, then you have another great way to save energy at home.  Most people keep the damper closed when the fireplace is not in use, but usually it is made of metal.  Chances are there is nothing stoping the flow of air through the chimney damper flap and out.  Using a very simple blow up type device can really help to move the needle and decrease energy usage and improve comfort.

A great way to save energy at home and improve comfort is to seal the chimney with an attic balloon.

The attic ballon has a stem that can easily be accessed to blow up the device and create a nice seal in the chimney.

Conclusion

High energy bills also typically mean uncomfortable homes.  The two go hand in hand.  So, if you follow these tips or decide to get an audit done and take advantage of incentives to get the work done, you are not only lessening your carbon footprint, but you will also be more cozy and comfortable as well.

________________

Written by Eric Gans
I have over 1000 energy audits under my belt in Maryland.  I like to take my personal experiences with each of my audit customers and try to get the things that concern them out into the world so others can make good home improvement decisions - in the right order - according to their needs.
 

Did these ideas help you save energy at home?  We want to know if you tried any of our solutions and how they worked out for you in the comments below!

Written by Eric Gans
 

I have completed over 2000 comprehensive home energy audits and hundreds of post-treatment test-outs. I have performed the tasks described in this article and I have also overseen technicians performing the work so that results, once the work is complete, are achieved.

If you want to know if you should air seal your attic, then you can ask yourself a few basic questions and quickly arrive at the answer. 

The easiest way to know is to determine if you have air sealing in your attic now.  If not, then you definitely need air sealing.

If you are not sure whether your attic is air sealed (who really wants to get in their attic?) then there are several things you can look for around the house that will tip you off. 

Tell Tale Signs You Need Air Sealing in Your Attic

The first tell tale sign is spider webs.  If you see spider webs dangling in recessed lights, near corners around mouldings in the ceiling or near the attic hatch, then you likely need to air seal your attic.

If you are feeling drafts around your home and different rooms seem more comfortable then others, particularly on extreme weather days, then you likely need air sealing in your attic and around other key areas of your home.

So, what is air sealing anyways?  Let's figure it out...

Reasons Air Sealing is Important

You don't have to be a home builder to know a little about how a house is made.  There certainly is no disputing that older homes, in particular, are not completely air tight.  We are able to breath when we are inside, after all.

So why is it important to seal up your house?  You need air to breath so what is the end game?

The biggest source of energy usage in a household bill is directly related to HVAC.  The less your HVAC runs, the lower your bill.  Pretty much that simple!

But, if your lucky, during extreme temperature days, your HVAC will actually catch up for a few minutes.

So, the idea when it comes to air sealing, is to prevent the air from flowing through those cracks in your building's shell, thus keeping it inside your envelope and keeping your home temperature more evenly controlled and comfortable.

Without effective air sealing in the attic, the R-value of your attic insulation actually suffers and that only adds to your woes. 

-Back to Top-

Envelope Air Leakage Variables

A super interesting physics concept should not be missed when it comes to air leakage in a house.  Without some force, air will not simply flow through a crack or gap.  Loss of energy through any imperfect connection point is dependent upon the following factors:

• Weather Dynamic Pressure**
• Size of Crack
• Shape of Crack
• Location of Unwanted Connection Point
• Material where the Weakness is Occurring

**Pressure related to weather also illustrates why on a severely cold day, for example, that it becomes difficult to regulate temperature and keep a modest energy bill. 

There are two factors at play. 

1. The weather outside creates a greater pressure inside, particularly when the gap between the two temperatures is very high (25 degrees outside/ 70 degrees inside).  Greater pressure acts to push your conditioned air through the cracks faster.

2.  It is cold outside so the HVAC is running and the additional pressure created by the air flowing actually works to push the air through those cracks simultaneously while trying to heat or cool a room to the desired temperature, effectively creating a conveyor belt of conditioned air being delivered to places that nobody in the family is hanging out (outside).

Making matters worse, of course, is the fact that all the while that is happening, fresh cold air is being drawn in from other cracks in lower portions of your home.

Typical Leakage Point in Basement

In summer the pressure in an attic due to heat forces air through the cracks and as a basic and general rule, hot follows cold.  So, in winter the warm air gets pushed up into the attic and in summer the hot attic air gets transferred down to wreak havoc on your AC unit and bills.

-Back to Top-
 

How to Air Seal

The general idea of sealing up a house is rather simple from 30,000 feet up. 

But, it can be kind of tricky when you are up in the attic and different ways the house is assembled creates unique air sealing opportunities.  Sometimes different situations call for different solutions.

Common air sealing materials include:

• Caulk or foam
• Sheathing tape
• Sheet metal
• 1/2" Polyiso (Rigid Foam Board)
• 3/4" Plywood
• 1/2" Drywall

A noteworthy takeaway from the list is that many common building components are listed as air barriers.  The key is sealing up the gaps!

Take a look at this new construction wall/framing assembly and the attention to detail that is given these days in some instances to sealing up a home.

Obviously, unless we are doing a complete remodel, this is not practical for finished areas in preexisting houses.  But, it does demonstrate the ways in which a home can leak and how to seal around any areas that are unfinished.

In a retrofit air sealing project, most of the "juicy" spots to seal are in the attic and basement. 

The video below shows a skilled technician air sealing the tops of walls (top plates), light fixtures and electrical wiring holes that were drilled when the house was built.  These are all places that air is traveling through, effectively escaping the inside if your "envelope" and costing you comfort and money.

The insulation is missing at the attic floor in the video and air sealing can be done when insulation exists as well.

-Back to Top-

Air Sealing Top Plates and Electrical Penetrations

When watching air sealing taking place it starts to make a lot more sense.  Of course, there is no way to actually see the air flowing through these tiny gaps in real time, but what does happen over time when there is insulation in place is that the air flows through and around around the insulation leaving dust and dirt in its track.

In the photo above taken at the top of the hallway push up attic access hatch is a great illustration of a few things. 

First, you will notice the electrical wires that are running through the top of the wall above.  The wires feed the hallway switch seen down below. 

The insulation around where the electrical wires are fed is discolored telling the story that is all too common in homes that are not air sealed.  Air is moving through those holes on the regular and air carries dirt and dust.  Over time it adheres to the insulation which proves this important point. 

Add all those holes up around your home and you have a nice big gap that can easily be the equivalent of having an open window in your home all year long.  Having the attic unsealed is actually worse than having a window open because of the pressure being the most at the ceiling pushing through more air leakage as a result.

Besides electrical penetrations, there are many other areas in the attic that should be air sealed.  More examples include:

• HVAC Chimney Penetrations
• HVAC Duct Penetrations
• The Attic Access Panel (pull-down stairs/ push-up hatch)
• Thermal Bypasses Due to Bulk Heads
• Knee Walls
• Recessed Lights
• Bathroom Fans
• Plumbing Vent Stacks
• Chimneys
• Electrical Box Bypasses
  
  -Back to Top-

Air Sealing Bathroom Exhaust Fans

Have you ever been in the bathroom on a cold day and wonder why it feels so cold in that area despite it being more comfortable in the adjacent room or hallway?  Sealing exhaust fans is an important nuance when it comes to attic insulation and they need special attention, particularly if you are experiencing temperature variance in rooms that they exist.

-Back to Top-

How to Measure Air Sealing Results

While listening to a podcast recently, I was struck by something that one of the hosts of the show said.  Essentially, the saying goes something like this: 

A measured project is a managed project.

There is nothing more true than this statement when it comes to air sealing an attic.  One of the most difficult things to do is check on the work once the attic is insulated.  Moving insulation around once a project is "completed" is grounds for decreasing the overall effectiveness of the work that was done.  That is obviously counter-productive. 

If you are doing this project on your own then the dynamics change and what I am about to say is not nearly as critical.

But, if you need to hire a professional, you should make sure that the company is going to perform a blower door test or air leakage test - before the work is done and after.  This way, you can measure the results of sealing up the cracks.

The blower door measures the house's "leakiness".  So, getting a flow number after can be compared to the initial number and results can be taken away in the form of a before/after.  

The best way to have this done is to get a home energy audit if you have that available in your area.  In Maryland, the local utility companies work within the Home Performance with ENERGY STAR parameters and it is a great program for the residents of the state.

Watch this blower door test example and what we did to get the right results!
 

The test works by pulling all of the air out of your house and as each little bit of air leaves it is immediately replaced by air from the outside of the "envelope", thus creating a flow at the fan that is measured in cubic feet per minute (CFM).

Here is another example of results with photos showing before the work and after with the accompanying signed test-out result form.

The actual result sign off sheet for the homeowner.

-Back to Top-

Health & Safety Matters to Consider when Air Sealing

Two building science principles every homeowner should know

• Air Changes per Hour
• Indoor Air Quality

Air Changes Per Hour (ACH)

Air changes per hour (ACH) can be defined as the amount of times the volume of air inside your home changes with the outside air.  It is the house "breathing" in effect. If your house is calculated at 7 ACH then you can expect that on any given day and during any given hour, the inside air will exchange with outside air seven times. 

ACH in new construction homes has to be very low (3 or less).  New building codes for energy efficiency are making builders install energy efficient measures at the time of construction so that all of the typical leakage points are sealed before walls and ceilings go up which makes those areas very difficult to treat after they are in place (like in preexisting homes).

Controlled vs. Uncontrolled Fresh Air

But, when we tighten up the envelope and don't allow the house to "breathe" as much we have to find solutions to create the right amount of ACH for healthy indoor air quality.  The key to this is to make sure the introduction of fresh air into the building is controlled so that less energy is consumed to maintain good indoor air quality (the right amount of fresh air) rather than allowing it to infiltrate uncontrolled causing heating and cooling systems to work much, much harder.

Indoor Air Quality - What is it Actually?

So in considering indoor air quality, it is important to know that measuring indoor air quality is NOT to measure the amount of particles in the air.  Indoor air quality is actually making sure that a building has enough fresh air and in a manner that is cost-effective.  Good indoor air quality also goes a long way towards sustainability and the longevity of the buildings structural components.

Combustion Safety

A home environment is subject to many different dynamics including pressure.  Pressure inside a home varies from house to house, neighborhood to neighborhood.  When a combustion appliance, such as a hot water heater or furnace is running, the conditions in the house could change the way the appliance runs.  If the change is too much for the system, it could cause a hazardous situation inside the home to unsuspecting inhabitants.  

Combustion safety testing for gas fueled houses is a key to a safely air sealing a home.  Much like the blower door test where the air leakage is recorded before any changes and after, the appliances are tested prior to any work being done.  Once the work is completed, the testing is conducted again to see if the resulting "tightening of the envelope" creates any spillage or adverse conditions inside the home.

Get Your Scores Today! - Home Energy Audit

A comprehensive home energy audit is a great way to have your home evaluated.  Measures can be prescribed in a way that will address indoor air quality as well as energy efficiency and comfort.  It is the whole house approach that ensures that you can have the best indoor air quality and a less drafty house at the same time.

-Back to Top-

________________

What do you think about air sealing your house?  We want to hear in the comment section below!

There are literally thousands of homeowners in Maryland that are a lot closer to having a more comfortable home than they ever could have imagined.

Let me explain...

In March 2021 I did a BGE energy audit in Howard County for a really nice family that just moved back to Maryland from a warmer part of the country around the end of summer 2020.

They reported to me that their first winter here was brutal. 

Cold spots at every turn, drafts in areas they enjoyed to spend time and the basement has been all but abandoned, despite having a nice playroom and a video game console with surround sound.  But on the coldest days it was just too much.

Two Reasons this Audit Makes a Great Case Study

First, the family was pretty much in the dark all winter about what they could do about their issues.  They love the home and the location, but something seemed wrong and they really did not know where to turn for solutions.  The HVAC was running continuously and never caught up.

Here is the other thing too - they just came off of having a home inspection done when they bought the property. 

What I have observed from time to time is that a home inspection gives homebuyers a false sense of security, particularly when it comes to insulation. 

The inspection is more in line with the old way of thinking about insulation...

I see pink stuff in the attic - all is good. 

The box gets checked and you, the end user, is puzzled by the drafts and looking at windows and doors for answers to why it is so cold.

But, as you will see, the inspector missed a few key things and did not give any guidance at the time that would assist the family in finding a swift solution.  So, instead, they spent the winter draped in blankets studying their window and door seals wondering if there was anything that could be done.

We cannot blame the inspector though.  Some of the key insulation concepts get lost on the best home inspectors.  It can get a little complicated.

The second thing that was fantastic about this scenario is that the BGE Home Performance with ENERGY STAR® program helped the family uncover their underlying issues and the incentives, available to all BGE and Pepco customers, paid for 70% of the cost in this case.
 

"The BGE Home Performance with Energy Star® Program will pay for 70% of the cost."

Sorry, that was worth repeating!

The part about all of this that gets my wheels spinning is how many other people are out there, enduring miserable winters, or hot summers for that matter, that could also benefit from this program in the exact same way.

This case study clearly demonstrates why an energy audit is such a critical assessment for a home to undergo. 

The same problems are happening in households everywhere in Maryland. 
  

Energy Audit - A Critical Home Assessment

An energy audit can illuminate comfort problems that would otherwise stay hidden in plain sight and this case study is a classic.

The Symptoms for this BGE Customer Case Study

-HVAC running all of the time
-Never really feel warm on the cold days
-Shockingly high energy bills
-Cold basement
-Drafty top floor
-Cold master bathroom
-Cold kids bedroom

I want to stop here and place a little emphasis on this list. 

I believe that this is where the disconnect exists for a customer that has these issues in their home and never gets an energy audit done.  

There is an expression that my dad would use - "if I had a nickel for every..."

If you add up all of my energy audits over the years, I would say that I would have fully completed roughly 1300 of them.  And, if I had a nickel for every customer that blamed their windows and doors - I would likely have 40 bucks (that is about 62% of the people if you don't wanna do the math).

The underlying message here is that if you have not gotten an energy audit because you think it is your windows and doors, then you might be surprised. 

Most people that have the audit done always seem quite enlightened by what is actually causing their problems.

The Case Study - Figuring Out the Root Cause

An energy audit is a process of gathering data points around your home.  The volume, square footage, foundation layout and type are all important to help you find the best solutions for making things better.

Sometimes, the first hour of an audit does not prove to be fruitful in terms of "opportunities" for improvements, or retrofits.  A well trained energy auditor never wants the cost of the project to outweigh the benefits.  An auditor is on the hunt for the low hanging fruit.

As an energy auditor, you can have some fun with this. 

It can be much like the game show Let's Make a Deal.  Every door you open to an attic or crawl space presents a unique set of circumstances that will either prove to be a great chance to move the comfort needle for the customer or it could be a dead end.

Now, this can also be kind of a slippery slope.  Great opportunities also come with a cost.  Meaning, if your home is stubbornly uncomfortable and the places that require insulation are under insulated and accessible that is fantastic because you can fix it!  But, it also means that you have to spend money to do so.

But, as mentioned, there are incredible incentives through BGE and Pepco available to help manage the cost.
 

Time to Investigate the Attic

This particular home has two sections of accessible attic space. One access point is in the hallway.

I took a trip up through door number one to inspect the attic space.

The first sign upon poking my head up is that the attic floor is insufficiently insulated.  One thing I have learned through the years is that those with some of the biggest issues have rolled batt insulation in the attic as this home did. 

Read what John Krigger and Chris Dorsi say about fiberglass batt insulation in the book Residential Energy: Cost Saving and Comfort for Existing Buildings

"All of the common facings attached to fiberglass batts are air barriers and most are vapor barriers.  However, their effectiveness as an air barrier depends on nearly flawless installation."

Fiberglass batt insulation is almost always not installed to perfection.

Now, I can't be sure about what I am about to say, but this is where I believe most energy auditors stop.  They take a quick peak at the attic and draw every conclusion for that specific attic area without proper investigation.

I take pride in going the extra few steps and I find that is usually proves to be beneficial - for my customers.  The rule is if I don't really want to go over to that spot then chances are not too many people do and therefore there could be a problem there that nobody has ever seen.

When I got in the attic and made a 180 degree turn, I saw what appeared to be a knee wall that was missing insulation.  The area was in a tough to reach part of the attic.

I decided to go around the corner to see what was going on because it was not quite making sense to me.  As with anything that you do on the regular, patterns emerge and a more comprehensive understanding of what you are doing comes over time - aka: experience. 

Adding to my sense of curiosity was the fact that during my initial tour of the home, the customer had pointed out to me that some remodeling was done in the vicinity below before they bought the home. 

A good home energy auditor has to be a like a sponge, absorbing bits of information throughout the time at the home so it can all be pulled together to produce sound solutions.

Then, once I was able to poke around the corner this is what I found.  A ten by ten area of un-insulated attic space hiding behind that wall. 

This is important for two reasons. 

Reason One - it speaks to the issues that they were experiencing on cold days.  Having insulation at the attic floor is the most important place to build the insulation boundary because the pressure is greatest.  

Hot air rises in a building and it wants to fly right out of the top and will if you let it.  Cracks and crevices are certainly big time issues for this, but because insulation slows the transfer of heat, the thin drywall alone is no match for the heat to escape at very high rates. 

Missing insulation is a big time issue. In an earlier article I wrote about how I examined the impact of an un-insulated three by six foot area in an approximate thousand square foot attic (2% if the area) equated to a 25% reduction in the overall R-value of the insulation in that particular attic.

Reason Two - it produces a larger incentive through the BGE Home Performance program.  Some of the rebate calculations are based on how much insulation an attic currently needs and when there is nothing, it pushes the incentive up. 

Missing the un-insulated area and modeling the home as if it did have insulation in that area would be cheating the customer.

My final mission while in this section of the attic was to determine if I could make passage to the other side of the home and I was able to confirm that I could not and had to use the second attic entrance.

Second entrance to the attic was located in the master bedroom closet.

More of the same in the second attic area.

The verdict is in!  This attic needs to be air sealed and insulated.  Time to run the numbers!
 

How Does this Program Pay for 70% of the Cost?

In order to help you understand how this program works, I will share the exact numbers from this project and how it worked out so favorably for this customer and you can hopefully gleen information to compare to your own situation and see if you can benefit like the family in this scenario.

But, if you don't have all or any of these characteristics in your home, that does not mean you will not qualify for rebates or that an energy audit won't uncover some totally different issue for you that will find a way to make it well worth your while.

The Numbers

Prioritized List of Energy Efficient Improvements

Total Cost of Improvements: $9500.00
BGE Incentive for this Project: $6640.70

Total Ratio: 70% of the total cost
 

Financial Analysis

A financial analysis will indicate annual realizations and provide simple payback years. 

How many home improvement projects actually pay you back?
 

Summary of Proposed Improvements

Whole House Air Sealing

When receiving rebates through the BGE Home Performance Program with ENERGY STAR, the blower door test is an integral part of the overall incentive structure and it is tied in many ways to each individual item listed on the list of improvements.

For example, when treating the attic on this project, by far the largest component of the improvement plan, sealing must be done at the attic floor so that the insulation performs to the R-Value it is designed to meet.

Basic Air Sealing

This is also a key to the whole house air sealing plan.  At the end the house is tested again for air leakage.  The overall leakage is reduced by the acceptable figure established by the program (10% minimum to qualify).
 

Rim Joist - Accessible

The top of the foundation wall in any home is leaky and needs to be sealed.  The question is how much of the area is unfinished and accessible to keep the cost vs. value in line.
 

Knee walls/Vertical Attic Walls/ Slope Transition Locations

Not all homes have knee walls so this section may or may not apply.  Knee walls are very difficult to visualize.  Photos can help.

Top photo: thermal image of the knee wall that is created by the transition from a sloped ceiling back to a flat 8' ceiling.

This image is taken at the exact same time the top thermal image was taken for point of reference.

This is a look at the missing insulation at the knee wall from the attic.

Attic Insulation - Sloped and Flat Areas

Once all of the "little" things around the attic and basement have been sealed and insulated and the attic floor areas have all been sealed, it is time to lay down the blanket..so to speak.

Blown Cellulose Demo

Improvement Results

Getting a considerable rebate on a project around the home that you still have to come out of pocket some money for won't be worth it if the results are not there.

The great thing about the BGE Home Performance with ENERGY STAR program is that we measure the results at the end.  This is done in a few different ways.

Visual Inspection

Once the work is done it is the responsibility of the energy auditor assigned to perform the final test to check the work that was done.  If they were not on the job, this can be done by simply looking in the attic.  The blower door test will reveal if air sealing was not completed, but it is very difficult to look for air sealing once the insulation has been installed.

Blower Door Test

The Blower Door Test

When the blower door test is done at the audit the "test-in" measurement is recorded.  A portion of the incentive and the customer's long term savings and comfort is also tied to the blower door test and that is why it is so important to the overall job process and the BGE program.

Here are photos of the actual blower door test results for this case study.  The numbers look really good!

Take a look at a short example of how we measure air sealing results with a blower door.

Customer Satisfaction - Measured Results

It is one thing to hit the mark on the numbers and achieve the goals when it comes to measuring the work that was performed.

Another part of a successful Home Performance with ENERGY STAR project is the customer's overall experience.  It certainly would be fantastic to have a more comfortable home with lower bills, but having a pleasant experience along the way should also play into things.

Based on a recent review by the customer on Google, it seems like we hit the mark on this one too!  Making this a successful project all the way around!

"Had a great experience with Eric and his team. Eric conducted our home energy audit taking time to point out and discuss the good and bad, answering all my questions. He also took care of the whole rebate process with the local utility. All phases of project completed in about 3 weeks. Easy and painless. Definitely recommend Eric and the Hometrust team!"

Read the Review Here
 

Need Advice on How to Do Something Like This?

If you are interested in making your home more comfortable and more efficient, give me a call.  We can discuss your situation and likely getting a BGE or Pepco Energy Audit is the way to go.  

Incentives through the program can be quite advantageous, particularly for those that know that they have to get this problem resolved once and for all. 

Furthermore, an energy audit can uncover other factors that can contribute to your specific issue as each home is different - even the same model across the street.

Give me a call!  I'd love to help you out!

Written by Eric Gans
I have over 1000 energy audits under my belt in Maryland.  I like to take my personal experiences with each of my audit customers and try to get the things that concern them out into the world so others can make good home improvement decisions - in the right order - according to their needs.

Most homes nowadays have air ducts that condition the inside of our living spaces.  Ducts are largely responsible for keeping us warm in winter and cool in summer.

And, yet despite their importance, they are often overlooked.  

Aside from the obvious, like making sure ducts are connected, there are other nuances that must be understood to prevent other potential issues.  For example, leaky ducts in summer in the wrong location might lead to condensation resulting in water damage to ceilings or wood.

This article will examine summer condensation issues related to ducts that run outside of the "envelope".  This would include ducts that run through a garage (the focus of this post), crawl space, attic or cantilever also known as an overhang.
 

Watch the Four Part Process First - Then Learn How it Came About

Part 1 -The blank canvas.  A fully removed plaster ceiling including the removal of nails and screws.  The area beneath the ducts has been swept and protective platic has been installed to keep the area clean and neat for the customer once the project is completed.

Part 2 -Application of the spray foam on the different areas of the HVAC supply plenum.  During this portion of the video, the foam bonds to the duct and seals and insulates rapidly.

Part 3 -Removal of excess insulation after it has fully cured.  This is done in preparation for the drywall ceiling installation later in the week.

Part 4 -A look at the completed portion of the duct sealing and insulation project to get a feel for the final product.

Initially - I Was a Little Worried About this Project

According to my eventual customer, the garage ceiling insulation project had already been contracted to be done and when the chosen company showed up to do the work, they promptly turned around and said it was too much for them to handle.  That, in turn, prompted the customer to call me.

But, when I went out to take a look at the garage and all that was involved, it did not appear to be too much as far as I was concerned and I quickly got to assessing the situation for the best way to get it done!

Insulated Ducts Are Not Sealed Ducts

If you so dare to pop your head in the attic and you see that your ducts are insulated you cannot simply assume that everything is in good shape.  Ducts are metal casings that have seams and connection points.  Not all duct insulation is designed to seal the small air leakage around seams.

Older ducts in older homes like the ones in the garage example below were not made as precisely as they are today.  Some systems have slots and cracks from shifts that occur normally in a home. 

Additionally, houses go through changes and therefore the paths that the conditioned air takes have to be altered.

One example can be seen commonly when the central furnace/ air conditioner is replaced with a larger unit at the same time an addition is being put on a house.  The larger system is now being called upon to provide heating and cooling to the new living space. 

During this process, the existing ducts are "tapped" so that new ducts can be run to the addition. 

It is during these re-configurations where some of the largest gaps and cracks can be detected in the ducts.  Of course, the ones you can get to should and can be sealed, but the harder to reach leaks in the areas outside of the "envelope" are the ones that can be trouble.

Garage Ceiling Example

In this example, the home was built in 1958.  For a home built in 1958, it was likely cutting edge.  Living space over a two car garage with a design that included ducts running through the ceiling to service the space above.  In theory, it was practical, efficient and ahead of its time.

But, as each and every Maryland summer would introduce new hot, humid air into the garage it would find its way more and more into the the space between the garage ceiling and the floor to the living space above and as the central air conditioner was improved and likely the sized increased - the ducts began to form condensation.

Drip...drip...drip...and eventually the water actually blew right through the insulation that was installed when the home was built (can be seen in photo below).  Soon after, the plaster ceiling began to deteriorate and it had to be partially torn down.

Photo taken during initial inspection.  Partial demo had already begun.

A little more perspective of the area to be treated due to duct condensation issues during summer months.
 

Making the Most of the Situation

The driving force for this homeowner to take on this project was the duct condensation and the long term issues that can come about if they go untreated.  But, another reason for taking this on was due to the cold bedrooms above during the heating season. 

It was clear that the old insulation methods and the unsealed and un-insulated ducts running through the outside garage ceiling were contributing to the comfort issues. 

So, the plan included insulating the entire garage ceiling area as well.  The plaster ceiling was removed on day one, insulation was applied and the area was cleared of all trash and debris. 

Day 2 

On day two the focus was on the main HVAC supply plenum (duct).  Final demo on the ceiling area that encapsulated the duct took place and preparations were made to seal the duct with two part spray foam.

Everything in the photo above is vintage 1958.  Sixty three years of water dripping down and creating a major blowout of the insulation, resulting in a damaged garage ceiling.

Special attention was going to be given to this area.  Since it was very close to where the HVAC air handler was located the pressure is greatest, therefore the more significant duct sweating that was taking place.

The Solution - Sealing and Insulating in One Shot

Two part spray foam is an effective treatment for a situation such as this one.  The removal of the ducts and the disruption and cost would outweigh the additional cost for the more expensive insulation material.  Getting behind to seal the tight spaces without having to remove flooring or support bracing is a great advantage of using spray foam.

You can see in the video the amazing capabilities of the liquid spray finding its way behind the ducts and moving to seal up the spaces that we know exist, but would have a tough time accessing otherwise.
 

Need Advice on How to Do Something Like This?

If you are interested in solving your duct condensation issue, give me a call.  We can discuss your situation and likely getting a BGE or Pepco Energy Audit is the way to go.  

Incentives through the program can be quite advantageous, particualarly for those that know that they have to get this problem resolved once and for all. 

Furthermore, an energy audit can uncover other factors that can contribute to condensation on ducts and the audit may uncover other solutions that render the need to insulate the ducts useless - while still solving the main issue.

Give me a call!  I'd love to help you out!

Written by Eric Gans
I have over 2000 energy audits under my belt in Maryland.  I like to take my personal experiences with each of my audit customers and try to get the things that concern them out into the world so others can make good home improvement decisions - in the right order - according to their needs.

Often times homeowners don't know what a Pepco energy audit is or how it can actually help.

For starters, a Pepco energy audit can help you avoid choosing the wrong solution to a problem around your home. An energy audit through Pepco is a good place to start a home improvement priority list. 

Take the important step of scheduling your Pepco energy audit as soon as you can!

Often times homeowners don't know what a BGE energy audit is or how it can actually help.

For starters, a BGE energy audit can help you avoid choosing the wrong solution to a problem. An energy audit through BGE is a good place to start a home improvement priority list. 

Take the important step of scheduling your BGE energy audit as soon as you can!

IECC Energy Code Testing - Blower Door Test

This beautiful new construction house that was completed in summer 2020 located in New Windsor, MD went through one of it's final steps to pass the energy code in the state of Maryland. 

The blower door test, or air leakage test was performed in accordance with the International Energy Conservation Code (IECC) and Maryland Energy Code Compliance. 

The air leakage code requires that a house test at equal to or less than three air changes per hour (3ACH). 

The test was conducted using the ASTM E1827 - single point method. 

The blower door test was conducted five times and each measurement was recorded and entered into the report. 

Each test result yielded an ACH number less than two so the house passed with flying colors. 

In Carroll County Maryland and many other counties across the country, it is important to consider the building envelope during each construction phase so that your house is sealed properly and it can also easily pass the test. 

Tighter houses use less energy and are more comfortable.  In a tighter house you control the home's "breathing" rather than letting your energy dollars escape through the  various holes to the outside around a typical residential building's shell.

Watch an explanation of the blower door test during a guest appearance at the Montgomery County Energy Connection video shoot.

General Guide to Air Sealing a Home

The blower door test will reveal whether these measures were properly taken during the construction of the home.

1. Air barrier and thermal barrier. 

• A continuous air barrier/pressure boundary must be installed in the building envelope.
• Exterior thermal envelope contains a continuous air barrier.
• Breaks or seams/joints in the air barrier must be sealed.
• Air-permeable insulation (fiberglass batts) should not be used as sealing material.

2. Ceiling/attic

• The air barrier/pressure boundary in any dropped ceiling/bulkhead/soffit should be aligned
• with the insulation and any gaps need to be sealed.
• Access opening, drop down stairs or knee wall doors to unconditioned space should be sealed.

3. Walls

• Corners and headers should be insulated and the junction of the foundation and sill plate must be sealed.
• The junction at the top plate and top of exterior walls should be sealed.
• Wall insulation should be in continuous alignment/contact with the air barrier
• Kneewalls should be sealed.

4. Windows, skylight and doors

• The space between window and door jambs and framing as well as skylights and framing should be properly sealed.

5. Rim Joists

• Rim joists should be air sealed (air barrier) and insulated.
• Floors (above garage/cantilever)

6. Insulation must be installed and affixed to the underside of the subfloor plywood.

• The air barrier must be installed at any exposed edge of the insulation.

7. Crawl Space Walls

• Encapsulation is recommended including installing vapor barrier at the floor, sealing and insulating the walls and disconnecting the space from the outside.

8. Shafts, penetrations

• Utility penetrations,
• Shafts for ducts
• Conduits for wiring
• Flue chases that open to the outside or unconditioned space should be sealed.

9. Narrow Cavities

• The proper insulation solution should be used to block and seal any irregular voids.

10. Garage Separation

• Air sealing should be done between the garage and conditioned spaces.

11. Recessed Lighting

• Recessed light fixtures installed in the thermal/pressure boundary should be air tight, IC rated and sealed to the drywall.

12. Plumbing and wiring

• Batt insulation should be cut neatly to conform to any wiring and plumbing located in exterior walls.

13. Shower/tub on exterior wall

• Outside walls connected to showers and tubs shall be insulated and the air barrier installed separating them from the shower and tub.

14. Electrical/phone box on exterior walls

• The air barrier must be installed behind electrical and communication panels/boxes or air sealed boxes should be installed.

15. HVAC duct measures

• HVAC register boots that go through the thermal boundary shall be sealed to the sub floor or drywall to eliminate leakage/waste.
• All ducts outside of the envelope shall be sealed and insulated to a minimum of R8.
• All ducts inside the envelope shall be sealed at the seams and any other cracks/crevices with Mastic.

16. Fireplace

• An air barrier should be installed on fireplace walls and the doors on a fireplace should be gasketed.

Watch the Blower Door Get Set up in 2.5 Minutes

Towson - Maryland

If you have a Cape Cod style home and you are wondering if you can air seal and insulate effectively - the answer is yes, however not without a good plan.

Houses with Cape Cod style framing stem from being built in the 1940s and 1950s when the cost of heating was dirt cheap and insulation was an afterthought.

Watch a few Cape Cod insulation techniques on YouTube

If you live in this style home, chances are very good that it has not been properly addressed due to the complexities of the way it was built. 

Below, you can take a peek at a recent Cape Cod insulation project and what steps were taken to seal and insulate.  This one is located in the friendly residential Southland Hills community of about 200 homes in the heart of Towson, Maryland.  The homes in the neighborhood were built in the 1940s.  

The Comprehensive Energy Audit

Having a home energy audit done when you live in a Cape Cod-style home might be a good idea if you are looking for guidance on how to properly go about creating better comfort and lower energy bills.

The good thing about working with an energy auditor who has experience is that you can gain insights and avoid pitfalls from a person who has seen these areas before and knows what to expect.

Partnering with a pro can help set you on the right path toward measurable results.

  Get a comprehensive home energy audit today!

Bonus Room House!

When I pull up to a home as an energy auditor I have my radar on:  What style home is it?  What is the footprint of the home?  What condition is the home in?  Is the heating and cooling gas or electric?  These are some of the take-off points to begin a great home energy audit.

One thing at this house stood out to me when I arrived.  

A window at the top of a wall within the side gable usually means the house has a "bonus room".  Another, more well-known way to describe the style of home is the Cape Cod style.

If you have a Cape Cod-style house then you know it really means the bonus room is really just an extra dose of difficulty.

The small attic behind the wall at the bottom of the sloped ceiling is usually hard to reach and a source of discomfort and dust due to old/worn insulation, poorly sealed hatches, and general basic neglect (nobody's judging ya!). 
 

     
Panel that leads to attic space behind bonus room wall.                     The attic area is behind the bonus room wall.

I find these attics in older homes throughout Baltimore County and Maryland for that matter and if you take a drive through this Southland Hills neighborhood, it is easy to see that many of the 200 homes built in the development are all of similar Cape Cod style.
 

How to Make Insulation Decisions in a Cape Cod

The complexities that arise when thinking about how to properly insulate a Cape Cod-style home start to go away the more you see this type of construction style.  The problem for most homeowners is that they are not traveling from home to home to manage insulation jobs, taking the time to figure all of this out.  

Furthermore, if you are not careful while expending brain power on thinking through how to insulate the roof walls or floor, other important things can easily get missed.

For example, HVAC ducts are typically living in Cape Cod-style knee wall attics.  It makes perfect sense.  It is an easy conduit to run ductwork to the different areas of the home adjacent to the attic as well as below. 

But, this can also bring a whole new set of issues if the ducts are not maintained or if they are old and have been subjected to other changes the house has undergone through the years.

Take a look at this discovery during a Cape Cod spray foam insulation project.

Finding a Good Air Sealing & Insulation Treatment Approach

The best approach to take in a house that is a Cape Cod configuration is to see what the house has to offer as a starting point.  What I mean by that is to figure out what areas of the space can be easily accessed.

Collar Attic Plan

Treatment to the top flat portion of the attic (called the collar attic) should be evaluated for treatment including sealing and adding insulation. If space permits air sealing and insulation should be installed.

Look at these similarly constructed homes with varying amounts of space above the top flat ceiling.  The lines indicate the approximate ceiling location.

Example Home with only 20" of space                                                     Home Where Audit was Conducted has 36" of space to work

 

In the two different configurations, literally the difference between 16" makes the difference between being able to work in the space or not.

The good news for this home in the Southland Hills neighborhood is that it had sufficient space for a human to work.

Check out some of the details...

The ceiling measures 7' across.                                                 A hatch that was cut for HVAC in the collar attic.
 

A pop up inside the space reveals not much room to move, but a good opportunity
to make improvements, nonetheless.

At the end of the day air sealing and adding insulation to the collar attic was feasible and recommended to the homeowner.  Each Cape Cod collar attic should be independently evaluated for feasibility.

Sloped Attic Approach

Sloped ceiling portions of a Cape Cod attic should be evaluated both visually and with thermal imaging.  One possible deterrent for homeowners to treat a Cape Cod attic is that finished sloped ceilings can be costly to re-insulate. 

But don't overthink or try to overdo the job.  With a few subtle installation techniques, the R-value in the sloped cavity can be increased in some cases, and treating areas that are more practical to reach will only improve the overall leakage of the ceiling bays.

The solution for this home was to seal the cavity bays from below and from above and leave the existing insulation to keep the project within budget.

Knee Wall Areas

Another challenge to getting measurable results when air sealing a Cape Cod-style home is getting to all of the small spaces between the roof and the knee wall.

In many cases, access will need to be made in several locations, so knowing this and prioritizing improvements is critically important.

As an example, don't re-paint the upstairs bonus room if you are considering insulation or if you are finding this article because you are not comfortable in the space and want to find solutions.

Energy auditing, home performance, and the BPI guidelines all work towards finding areas around preexisting homes to treat where the return on investment is positive over time. 

In some instances, costs will outweigh value, but when it comes to treating these inaccessible spaces that have older insulation - the gains in energy savings and comfort can really pay off if a little finishing work is required after the project is done adds a little to the overall cost.

Every situation should be evaluated on a case-by-case basis and a home energy audit is precisely a way to figure all of this out.

Notice how the front dormer windows create multiple areas that need to be treated, making it a bit more difficult.

Check out how we create access to an attic area that is not currently accessible.

Final Plan: Sealing and Insulating in the Best Locations for this House

The stack effect drives the air change conveyor belt inside your home quite a bit in the heating season. This is due to leakage in the basement and in the attic.

During an energy audit, I am literally "on the hunt" for places where air can infiltrate (come into your conditioned space) and exfiltrate (your conditioned air goes out).  Sealing up these two places in cost-effective ways is the name of the game!

So, after careful review and consultation between myself and the homeowner, we decided on the following work scope:

~WORK SCOPE~

Basement Rim & Band Joist - Every Home Should Get this Treatment by the Way

If you are not sure what the rim and band joist are in your basement and if it is accessible for treatment - you are about to find out!

First, put yourself in the unfinished part of your basement.  Usually, it is a utility room with an HVAC, a water heater, and maybe a washer/dryer.

Identify your foundation wall at the top and you have found your rim and band joist.

Take a look at how the electrical "main" is coming through the rim joist in the basement of this Towson, Maryland home performance home.  This is happening in a lot of homes.

Look at the size of that hole.  And this is the point - it is a hole going directly to the outside which means this:

Summer: humidity infiltration
Winter: cold air infiltration

Just look at those spiderwebs.  The spiders like to make their traps where the air is moving.  It is instinctual.  So if you see a spider web, air is flowing.
 

Now get your full frame of reference by watching this short video clip that shows where the electrical main and gas line enters into the rim joist from the outside which appears "invisible", but it is not.

Results - A Look at the Final Project and the Test-Out Numbers

Rim and Band Joist Treatment - Closed Cell Spray Foam
 

Watch the spray foam team treat a portion of the rim and band joist in this up close and personal clip. 

Knee Wall Attic Treatment Before / After

Example of Knee Wall Encapsulation

Blower Door Results

Many factors drive the overall reduction in leakage that each home is scheduled to achieve during a home performance project through the BGE program.  I make this very clear to my customers that for every house I believe we can get a 30% reduction and if there is a home that I am convinced we can only achieve the minimum required to meet the program standards (10%) - only to exceed that by a lot.

As a result of many audits and challenging situations when I was wrong, the partnership I formed with this customer went a long way.  We both agreed that a 20% reduction was a good target and that due to other factors that were not reported here, we will do everything we can to nail the work scope and see where it takes us.

Ultimately, this home performance project achieved an 11% reduction in leakage.  

Initial Blower Door Test In CFM: 3775 Cubic Feet Per Minute at Negative Pressure -50 Pascals

Final Test Out Number: 3255 Cubic Feet Per Minute at negative pressure -50 Pascals

Need Advice on How to Do Something Like This?

If you are interested in making your home more comfortable and more efficient, give me a call.  We can discuss your situation and likely getting a BGE or Pepco Energy Audit is the way to go.  

Incentives through the program can be quite advantageous, particularly for those who know that they have to get this problem resolved once and for all. 

Furthermore, an energy audit can uncover other factors that can contribute to your specific issue as each home is different - even the same model across the street.

Give me a call!  I'd love to help you out!

Written by Eric Gans
I have over 1000 energy audits under my belt in Maryland.  I like to take my personal experiences with each of my audit customers and try to get the things that concern them out into the world so others can make good home improvement decisions - in the right order - according to their needs.

Written by Eric Gans

I used to be a window contractor. More recently, I have tested thousands of windows as a certified energy auditor. 
-2-6 min. estimated read time to get the information you need

Table of Contents

As a former window contractor turned certified home energy auditor I have been on both sides of the coin when it comes to replacement windows. 

Early on I was convincing people (with the right intentions and wrong information) to replace windows to solve draft issues.

Now, I am on the other side getting called out for an energy audit to check windows because the new and old windows always seem drafty.

In fact, most people immediately connect comfort problems to windows and doors. 

But, it usually turns out to be bigger problems that are lurking and they don't cost nearly as much to fix!

It took me years to figure it all out, but when you stop and think about it all for a moment - it really makes a lot of sense. 

Here are five reasons that can help you answer the question:

Why do my windows feel drafty?

-Back to Top-

1. The Windows Are Not the Draft Source to Begin With

FACT:  Windows Account for Only 10% of Total Air Leakage in a Typical Home

 

A misconception for most homeowners is that windows are the only location in your home's "shell" that air can get in and out. 

But, there are many other places around your house that might be much more connected to the outside than windows.

And, a lot of these gateways are hiding in plain sight!

If your home is stubbornly drafty you need to think about the issue in three-dimensional ways.  This does not mean that you wasted money on windows or that you need special glasses.  It just means that you need to shift your hunt for the drafts by starting to look up and down instead of only through the sides.

FACT:  Air needs some help to get through cracks and crevices around your home and the pressure inside your home is greatest at the top (attic) and at the bottom (basement/ crawlspace).

"If your home is stubbornly drafty you need to think about the issue in three-dimensional ways...shift your hunt for the drafts by starting to look up and down instead of through the sides." 

Read on to learn about the stack effect and how getting the basics from this physics phenomenon can help you begin to think in three dimensional ways about drafts.

-Back to Top-

WATCH ON YOUTUBE

2. Understanding Stack Effect & How it Can Solve Your Draft Issue

In the book Rich Dad Poor Dad by Robert T. Kiyosaki, he talks about how as school children we are never really taught the vital lessons of personal finance and how to stay out of debt and save for the future. 

Similarly, I say everyone should learn about the stack effect when ready to purchase a home. 

Understanding how it can play a big part in drafts around the house can really help you with better comfort and overall energy efficiency.

The stack effect can be simply understood by taking one concept we all learn as young children:  Hot Air Rises

Here is the part they don't tell you when it comes to your home.

When the warm air rises in your house it creates a lot of pressure at the top and it escapes through all of the holes in your ceiling right up into the attic if modern insulation techniques are not in place.

Many of the holes where this is happening you cannot see, but they do exist!

Check out this 15 second video that demonstrates one common place air escapes at the top floor ceiling.

This problem causes a conveyor belt in a sense. When the warm air goes out at the top new cold air gets drawn in down low - from the leaky parts of the basement or an open crawl space.

As an example, the stack effect is the reason recessed lights in the top ceiling and rim joists down around the foundation should receive way more attention than windows.

Older, slotted recessed lights are no match for the warm air pressure, causing a warm air LEAK!  As it leaves, cold air comes in from down low. 

As a result - your comfort and money go in the attic and you feel drafts.

An Energy Audit Can Point Out Basement Air Leakage

Shown: Air Leakage in Basement @ Top of Foundation Wall (rim joist) During Blower Door Test
 

-Back to Top-

3. Fireplace Flue & Recessed Lights - Sealing Up "Gateways" to the Outside

One easy way to find drafts is to look for the "gateways" to the outside. 

For example, one out of every five customers that I do an energy audit for does not have the flue shut on their fireplace chimney which is a huge gateway to the outside.  

Recessed lights are also gateways to the attic (outside) and it is a good practice to check the dampers on any exhaust fans you have venting to the outside. A mis-aligned, damaged or non-existent damper can be a real draft maker.

Sealing Solutions

• Covering and sealing can lights at the attic floor
• Improving household exhaust terminations
• Use a chimney "balloon" to seal faulty flue dampers

Watch How we Seal Big Holes in the Attic

Then We Measure How Much We Sealed the House

Here is Something to Chew On:
Your window contractor will not measure this for you.
 

-Back to Top-

4. Improperly Treated Crawl Space/ Basement

If the construction style of your home is on a crawl space that is open, then you might experience high drafts. 

An open crawl space will allow unconditioned air into the the crawl space and unless there is a proper pressure boundary separating the crawl space from the room above, then drafts will surely occur.

Open crawl spaces traditionally have vents in the foundation wall.  The theory is to allow fresh air into the space and keep it dry, but in actuality the complete opposite happens in summer.  Crawl spaces become breeding grounds for insects, moisture and both want into your house!  In winter it is a constant source of cold air into your home.

If you have a full basement it is very likely that the rim joist in any finished or unfinished area has not been properly air sealed and this will allow air infiltration in the basement area that will cause drafts through walls and floors into the living space above.

Check Out this Test I Did
I tested the house before any work, after air sealing, and then after the windows.
Can you guess which was more effective?

-Back to Top-

5. Improperly Installed or Misaligned Windows

Another possibility for drafty new windows, however the least likely, is that the windows were installed improperly or worse yet, not caulked and sealed. 

Even if this is the case, it would still be difficult to make a draft problem worse with new windows even if the windows are incorrectly installed due to pressure dynamics in a house. 

It is important to note however, that basement windows and windows on the second floor could be susceptible to leakage if not properly installed and sealed due to higher pressure.

Make sure your windows are fully closed and locked!
Another common issue that homeowners with new replacement windows have problems with is making sure that top sash in double hung windows (most common type) are pushed all the way up in the u-shaped header.

When new window users are not accustomed to both sashes of the windows being operable, the thought that the upper sash dropping down does not come to mind and the notion that the windows are leaky is the typical conclusion.  Operable windows have several parts that all work together for peak performance.  If one thing is slightly off track, the rest of the system can suffer.

Watch: Window Installation Steps
 

Watch: Air Sealing Windows
 

-Back to Top-

Drafty Window Solutions: What will actually work?

Get a Comprehensive Home Energy Audit

A great way to deal with the issue of drafty new windows is to have a comprehensive home energy audit performed. 

An energy audit includes a blower door test so you can find the sources of your drafts.

A great energy auditor will guide you to better comfort with knowledge and diagnostic tools.

If you decide not to have an audit then you can sign up for this blog or read this article about the unobvious ways in which your home is inefficient.

-Back to Top-

________________

I would like to hear your comments about this article.  Feel free to post something below...